Accessories
Sheath Fault Finding 'A-Frame'The A-frame accessory is used to detect ground faults on pipes and cables. In the case of pipes, the faults consist of coating defects. In the case of cables, faults are usually caused by insulation damage allowing the metallic sheath (or internal conductor) to become in contact with the ground.
Inductive Clamp
VX2/50 Clamp:
Clamp is used to apply the transmitter signal to an insulated line, removing the need to connect the transmitter signal directly to a conductor or cable sheath. Dia. 2in (50mm).gif)
VX4/100 Clamp:
An accessory used to apply the transmitter signal to an insulated line, removing the need to connect the transmitter signal directly to a conductor or cable sheath. Dia. 4in (100mm).
.gif)
VX5/125 Clamp:
An accessory used to apply the transmitter signal to an insulated line, removing the need to connect the transmitter signal directly to a conductor or cable sheath. Dia. 5in (125mm).
VX18/450F Clamp:
A flexible clamp used to apply the transmitter signal to an insulated line, removing the need to connect the transmitter signal directly to a conductor or cable sheath. 18in Flexible (Circumference 450mm).
LPC Separation FilterThe LPC separation filter (LPC) is used to safely inject a trace tone to a live cable via a domestic mains socket, so that the cable can be traced from the premises to the connection in the street. It is suitable for connecting to voltages between 100V AC and 250V AC.
Remote AntennaThe remote antenna can be used to help identify a particular cable on a cable tray or where cables are bunched together.
Bluetooth ModuleAs an optional, the vLocPro2 and vLocML2 receivers can be fitted with a Bluetooth communications accessory. The Bluetooth option can be retrofitted and can be ordered at a later date if preferred.
Direct Connection LeadUsed to connect the transmitter to a line using the direct connection method.
Ground SpoolUsed to extend the ground connection to a suitable grounding position.
Banana Plugs AdapterAdapts the direct connection crocodile clip to banana plug allowing the direct connection leads to be connected to a banana socket.
Transmitter accessories
Loc-1Tx Alkaline Battery TrayAlkaline battery tray for Loc-1Tx transmitter. Requires 4 x Alkaline D cells.
Loc-5Tx Rechargeable Battery PackNiMH rechargeable battery pack for Loc-5Tx transmitter.
Loc-5Tx Alkaline Battery TrayAlkaline battery tray for Loc-5Tx transmitter. Requires 8 x Alkaline D cells.
Loc-5Tx/10Tx Charger
Mains charger (100-250V AC input) used to charge 5 Watt or 10 Watt transmitters rechargeable battery packs. Supplied as standard with rechargeable battery option.
Loc-10Tx Rechargeable Battery TrayNiMH rechargeable battery pack. Only use charger supplied.
Loc-10Tx Power Lead12V DC, 30ft (10m) lead to power the transmitter from a vehicle. Note, this is NOT a charge lead.If it is intended to apply the transmitter to a target line at high output levels and long periods, it may be useful to power the transmitter using the 12V DC vehicle power lead. To power the transmitter from the 12V DC vehicle power lead, connect the lead to the 12V DC input positioned on the side of the transmitter. Plug the cigarette lighter plug into the vehicle cigarette lighter socket (be sure that the socket is live. Some vehicles only activate the cigarette lighter when the vehicle is running).It is not necessary to disconnect or remove the standard batteries as the unit will automatically select the external 12V DC supply.
Loc-10Tx Outdoor Power Supply
100-240V AC to 12V DC, 30ft (10m) lead to power (NOT charge lead) the Loc-10Tx transmitter from the mains supply.
Receiver Accessories
Receiver Lithium-ion Rechargeable Battery PackThe Lithium-ion rechargeable battery pack is supplied as standard for receivers. Charging is done with the battery inside the receiver.
Receiver Standard Battery Charger
The receiver Lithium-ion battery charger is supplied as a standard item. It is powered from the mains supply. (100-250V AC)
Receiver Alkaline Battery Holder
This alkaline battery holder is supplies as standard and is used in the event the rechargeable battery pack has fully discharged. It can be considered as a backup battery pack. It requires 6 x AA alkaline batteries.
Receiver Vehicle Charging Lead
12ft (4m) long vehicle charging lead to charge the receiver’s battery (Lithium-ion) while on the move.
Sondes:
A small transmitting coil which may be built into a product such as a sewer camera or packaged as a small self contained battery powered transmitter. A receiver tuned to the same frequency can locate the position and depth of the Sonde and hence whatever it is attached to or in. Frequently used for locating sewer cameras, and the non metallic pipes.
D18-33-SR44 Sonde- 0.7in (18mm) x 3.2in (80mm) long
- frequency: 33 kHz
- range: 15ft (4.5m).
- 2 x button cell batteries.
D38-33-AA Sonde- 1.5in (38mm) x 4.1in (105mm) long
- frequency: 33 kHz
- range: 16.3ft (5m).
- 1 x AA battery.
.jpg)
D23F-512-AA / D23F-640-AA Sonde- 0.9in (23mm) x 17.3in (440mm) long
- range: 20ft (6m).
- “Flexible (3 section) Sonde with optional 512Hz or 640Hz for use in cast iron pipes”.
- 1 x AA battery.
D64-33-LR61 Sonde- 2.5in (64mm) x 7.3in (186mm) long
- frequency: 33 kHz
- range: 26ft (8m).
- 1 x LR61 battery.
D38-83-AA Sonde - Dimension: 1.5" (38mm) x 4.1" (105mm) long
- Frequency: 83 kHz
- Range: 16.3ft (5m)
- Power Supply: 1 x AA battery
D64-09-LR61 Sonde
- Dimension: 2.5" (64mm) x 7.3" (186mm) long
- Frequency: 9.82 kHz
- Range: 26ft (8m)
- Power Supply: 1 x LR61 battery
D64-83-LR61 Sonde
- Dimension: 2.5" (64mm) x 7.3" (186mm) long
- Frequency: 83 kHz
- Range: 26ft (8m)
- Power Supply: 1 x LR61 battery
MyLocator2MyLocator2 configuration tool is a software package that enables the operator to configure the vLoc series 2 of locators.
MyLocator2 allows operators
- To transfer data from the locator to a host computer.
- To perform software upgrade
- To add splash screen to the receivers
- To save the receiver configuration or use the saved configuration on other receiver